Driver USB to serial: supported devices vendor ID
SUMMARY 2016-05-10
(last update)
- The
USB-to-serial
devices drivers supported by Gekkota are:- PROFILIC (vendor ID hex: 067b) and
- FTDI (vendor ID hex: 0403)
INFORMATION
- The goal of this documentation is to install serial interface on a USB connector
- for example to use AVCmd Serial Web IDL
- For SMA300, beware of using the appropriate
uart_1
oruart2
in Web IDL AVCmd serial html file
- For SMA300, beware of using the appropriate
COMPATIBILITIES
- SMA300 (PSN not supporting WWAN)
- Gekkota 3.12.31 (or above)
CONFIGURATION OF YOUR SERIAL INTERFACE
- These preference are permitting to configure your serial interface
- innes.adapter.serial.uart_1.config
- innes.adapter.serial.uart_1.syspath
- innes.adapter.serial.uart_2.config
- innes.adapter.serial.uart_2.syspath
- innes.adapter.serial.uart_3.config
- innes.adapter.serial.uart_3.syspath
- innes.adapter.serial.uart_4.config
- innes.adapter.serial.uart_4.syspath
- Defaut value
- innes.adapter.serial.uart_1.config
{"baudrate":9600,"parity":"none","stopbits":"1","flowcontrol":"off"}
- innes.adapter.serial.uart_1.syspath
/dev/ttyUSB0
- innes.adapter.serial.uart_1.config
- In case you are using USB-serial adaptor 4->1, 3->1 or 2->1, it is advised to change the syspath for uart_2, uart_3 and uart_4 to respectively,
/dev/ttyUSB1
/dev/ttyUSB2
/dev/ttyUSB3
WHAT ABOUT OTHER VENDOR ID
- These other vendors showed below are not supported because they have been deliberately inactivated in the source code to save memory code place
- ADI
- ATMEL
- BAYER
- DE
- ELEKTOR
- EVOLUTION
- FIC
- GN_OTOMETRICS
- ICOM
- IDTECH
- INTERBIOMETRICS
- IONICS
- JETI
- KOBIL
- KONDO
- LARSENBRUSGAARD
- MARVELL
- MICROCHIP
- MOBILITY
- MTXORB
- NEWPORT
- OCT
- OLIMEX
- PAPOUCH
- PI
- POSIFLEX
- QIHARDWARE
- RATOC
- RTSYSTEMS
- SEALEVEL
- ST
- TELLDUS
- TESTO
- TML
YOU DON'T REMIND THE VENDOR ID OF YOUR ADAPTER: GET IT WITH LINUX COMMAND
- In case you don't remind the apaptor device vendor, it is possible to retrieve it with a linux command line (patch installation is required to navigate in the linux file system, contact support.innes.pro for more information),
- disconnect your adaptor USB-serial
- type: lsusb
- ex
Bus 001 Device 004: ID 0424:2514
Bus 001 Device 001: ID 1d6b:0002
- ex
- type: lsusb
- connect adaptor USB-serial, and your device appears
- type: lsusb
- ex
Bus 001 Device 004: ID 0424:2514
Bus 001 Device 001: ID 1d6b:0002
Bus 001 Device 006: ID 067b:2303
- The added line is corresponding to your own adapter
- Description
- in the line
Bus 001 Device 006: ID 067b:2303
,- The vendor ID is the first value (ex:
067b
) - The device ID (or product ID) is the second value (ex:
2303
) (2303 = Device 2303 HXA)
- The vendor ID is the first value (ex:
- in the line
- Information - typing vendor ID in a Web browser ("vendor ID" + "067b") should lead to the name of your adaptor vendor
- ex
- type: lsusb
- disconnect your adaptor USB-serial