Firmware and documentation for DMB300
RELEASE NOTE
IMPORTANT: one specific license key is required per each DMB300 device that must run on Gekkota 5 middleware.
IMPORTANT: After migration, in case using third party software to publish App, your previous Apps may be not compatible. For further information, contact support@qeedji.tech
IMPORTANT: In case you wish to upgrade your DMB300 devices from Gekkota 3 middleware (3.12.57) to Gekkota 5 middleware (5.YY.ZZ), it is highly recommended to contact support@qeedji.tech to know the impact of this migration. Check also the software compatibilities below, and remember that you cannot downgrade to a Gekkota 3 middleware afterwards. The specific DMB300 RMA (or Return Merchandise Authorization) consisting in downgrading the middleware Gekkota 5 back to the middleware Gekkota 3 is not covered by the warranty of the device.
Never make electric unplug on your player while software upgrade is in progress (green led blinking 6 times every 4 seconds) else the player may not be able to work properly
2023-02-01
V5.10.11 download
BUG FIX, NEW FEATURES, MINOR UPDATES
- Change: the default value for the innes.image.max_size preference is now 4096 px
- Fix: the UDP stream playback could stop after a couple of seconds with some specific streamer configuration
- Fix: if the audio codec of a .mov media was not supported, the video track of the .mov media was not decoded
- Fix: the WLAN network interface with these security ciphering value was not working
none
WEP
WPA-Personal (PSK)
WPA2-Personal (PSK)
WPA-Enterprise (EAP)
WPA2-Enterprise (EAP)
- Fix: the content of a remote image having a same name could be not updated
- Fix: MS-PowerPoint medias playback
- the video embedded in MS-PowerPoint media could be unexpectedly shifted on the left when the slide aspect ratio was 4:3
- the failover font researching from the Microsoft cloud was not working
- Fix: the scrolling text was not displayed properly when the output rotation was 90° (or 270°)
- Fix: the GPIOs reading and writing on Jack 3.5" connector and on Phoenix connector was not supported
- Fix: in some case, when the output resolution was 90° (or 270°), the test pattern for the WLAN network interface was displayed outside the white outline
- Fix: with some specific output resolutions, the STATE: up or STATE: down information could be not displayed in the test pattern
LIMITATIONS
- XPF servers are not supported
- AV commands are not supported
- the audio may be not synchronized accurately with the full HD .ts media when the output resolution is 1920x1080
- transitions between MS-PowerPoint slides are not supported
- the DVB-T peripheral card is not supported
- the bitrate limitation is not supported
- the colour adjustment is not supported
- IR on Jack 3.5" is not supported
- the device must restart at least once with the appropriate WIFI security ciphering value after the security ciphering of the WIFI router is modified
- the GPIO Jack 3.5" can be used in output only when the Phoenix GPIO are configured as disabled
- the playback of live video Web contents is not properly supported
INFORMATION
SUPPORTED MEDIAS
- Devices supported medias and performances download
QEEDJI POWERPOINT PUBLISHER FOR MEDIA PLAYERS
CONFIGURATION SCRIPT
KNOWN LIMITATIONS
- Media Source Extension
- In this version, the playback of all other MSE contents playbacks, meaning MSE video content displayed in an area inside the HTML page, without any device reboot is not guaranteed
- About the
Media Source Extension
JavaScript:- Each MSE content provider has its own algorithm implementation in its MSE JavaScript. Consequently, it is possible that some MSE content having a specific MSE JavaScript is not fully supported making that the video does not start properly (for example, with some MSE video content replay)
- When playing a MSE content, an error message if playback doesn’t begin shortly, try restarting your device could be displayed sometimes after a while telling that the video has stopped and will not start anymore. To work around, play another media, then play again the MSE content. The best practise consists in playing the MSE content URI with a fixed duration (ex: duration 1 hour).
- About other MSE content: for example, the MSE video content displayed in a thumbnail inside the HTML Web page:
- Warning: the MSE content provider can decide at any time to remove a content. So an MSE content can be available one day and not available the day after
- When the MSE content is displayed in a thumbnail inside the HTML Web page, a lot of other objects need to be displayed as well and could require a lot of memory. Depending on the Web page played, the device could sometimes reboot after having played it after a while. The
W3C
is working on to improve theMedia Source Extensions
specifications so that the MSE Javascript is more suitable also for devices that have a limited available memory amount
- To inactivate the DASH MSE feature,
- Set the user preference
media.mediasource.enable
tofalse
. The error message An error occurred. Please try again later (Playback ID: ...) should be displayed when trying ten to play an MSE content in this condition. This message could be seen also when playing another video at the same time when the dual video decoding is not supported on this device.
- Set the user preference
- Note for MS-PowerPoint bullets
- Ensure that the appropriate fonts are properly embedded in the content
- Not yet supported in MS-PowerPoint medias rendering:
- Animation
- Effects
- WordArt, shadow
- Images
- Image with filtering
- Emf
- Animated image
- Gif & Png (displayed but not animated)
- Some shapes
- Smart Art
- Multi-colors shape texture
- Text
- Kerning is not supported
- Audio & video
- Vertical fading (in case mixed horizontal & vertical fading)
- Font
- Embedded
- Fail over & substitution fonts
- OLE injection (MS objects)
- Slide hiding
OLD VERSIONS HISTORY
2022-12-19
V5.10.10
BUG FIX, NEW FEATURES, MINOR UPDATES
- initial version